Coffee Plunger 600ml


SKU: 119 Category:


The french press (coffee plunger) is a classic coffee maker – one that we think is pretty under-rated. It’s been around for the better part of a century and it still is one of the quickest and easiest ways to make delicious coffee. It’s also a great brew method when you’re making coffee for a few people, as you can buy one in a larger size and brew more or less without affecting the flavour.

Because coffee plungers use a wire-mesh rather than a paper filter, they produce full-bodied cups, full of flavourful coffee oils. This makes them a great way to fully experience the natural characteristics of a coffee.

How To Get The Best Out Of Your  Coffee Plunger
Whether you call it a french press or a coffee plunger (or anything else for that matter), there’s a pretty good chance you’ve got one in your home. These classic coffee makers are everywhere, but tragically, they’re often held in poor regard. In reality, the biggest problem with the french press is that most people just don’t use it correctly.

What You’ll Need

Coffee plunger (even that old one at the back of your cupboard will do)
A coffee grinder
A kettle to heat your water
Something to stir with (ideally not metal if you don’t want to scratch your glass)
A kitchen scale to weigh your water
A more precise coffee scale to measure your coffee (if possible)
A timer (most phones have one if your kitchen doesn’t)
Step 1: Decide how many you’re brewing for & put the kettle on
One of the great things about the coffee plunger is that they come in all different sizes and it’s one of the few brew methods that isn’t much affected by the amount of coffee you’re brewing. Use a ratio of 60g/L; for instance:

1 mug: 15g coffee & 250ml water
2 mugs: 30g coffee & 500ml water
3 mugs: 45g coffee & 750ml water
4 mugs 60g coffee & 1000ml water

Step 2: Weigh & grind your coffee
The kettle will take a while to boil, so this is a good time to weigh out your coffee beans using the 60g/L ratio. Set your grinder to a coarse setting. For most home grinders, the coarsest is a great place to start. On the Severin Coffee Grinder, we use setting 10. Ideally, wait till the last convenient minute to grind so your coffee is as fresh as possible.

Step 3: Pre-heat your brewing vessel
When your kettle has boiled, pour some of the freshly boiled water into the brewing vessel to pre-heat it. A lot of heat will be lost as you brew, so by pre-heating, you keep the brewing temperature a bit more constant.

Step 4: Let your brewing water settle to ~93°C
During this time, you also need to let your brewing water come to ~93°C. A thermometer is handy here, but depending on your kettle, you need to wait around 1-2 mins after boiling to get in the right temperature range. Erring towards slightly cooler rather than hotter is probably a good idea if you don’t have a thermometer. Water that is too hot will scald your coffee and make it bitter!

Step 5: Discard your vessel-heating water and add the coffee grounds to the bottom of the plunger.

Step 6: Set a timer for 4 mins and put your plunger on top of a ‘zero-ed’ scale
Timing your extraction is very important. Too short and your coffee will be sour and acidic. Too long and your coffee will be bitter. Don’t leave it to chance – use a timer!

In a similar vein, you need to make sure you’re using the right amount of water, and the easiest way to do that is to use a kitchen Scale. 1ml of water weighs 1g.

Step 7: Bloom your coffee with a bit of water (2-3x coffee weight)
It’s good practice to start by encouraging the gases to escape from your coffee (called blooming) before adding the rest of the water. Try to start your 4 minute timer just as you pour the first bit of water onto the coffee. Aim for 2-3x the mass of the coffee you’re brewing (you don’t need to be super precise here) and give it a good stir. You should see the gases escaping and creating foam.

Step 8: Add the rest of the water to your desired weight/volume
Do this slowly & methodically, trying to get even contact with all of the coffee. Give it a stir once the water is all in.


Step 9: Stir again every minute or so
To encourage a full extraction, give the coffee a gentle stir every minute or so. Don’t do it too vigorously to avoid over-extraction but just a little movement to avoid the grounds settling. We don’t find that you need to put the lid on while the coffee is extracting, but opinions differ on this topic!

Step 10: Plunge at 4 minutes & serve or decant immediately
Once your timer sounds, plunge the coffee all the way to the bottom (don’t be shy) and quickly serve or decant. The wire mesh in your coffee plunger does not completely separate the coffee from the water so if you leave it in there, it will become over-extracted & bitter.


Additional information


Black, Grey, Red

You may also like…